Commit 20e26d22 authored by Philip Hozier's avatar Philip Hozier
Browse files

final project - electronics 11/5 update #1

parent 76b9ae49
Pipeline #229776 passed with stages
in 22 seconds
......@@ -182,8 +182,8 @@ button as an input source to trigger the output response of the board.
| **COMPONENT** | **DESCRIPTION** | **DATA SHEET** | **SPECIFICATIONS** |
|---|----|---|----|
| **3 UPDI Header pins** | To allow board programming/UPDI communication. Plus power 5v | | Non-polarity. |
| **ATtiny1614** | More pins than the ATtiny1614 | [ATtiny1614-16-17-DataSheet-DS40002204A.pdf](../week12/ATtiny1614-16-17-DataSheet-DS40002204A.pdf "ATtiny1614 datasheet") | Polarity |
| **Voltage regulator** | To drop the input voltage by 1.2 v for the sensor. | [LM3480_datasheet.pdf](../week10/lm3480.pdf) | Polarity |
| **ATtiny1614** | More pins and memory than the ATtiny412. | [ATtiny1614-16-17-DataSheet-DS40002204A.pdf](../week12/ATtiny1614-16-17-DataSheet-DS40002204A.pdf "ATtiny1614 datasheet") | Polarity |
| **Voltage regulator** | To drop the input voltage by 1.2v (to 3.3v) for the sensor. | [LM3480_datasheet.pdf](../week10/lm3480.pdf) | Polarity |
| **Capacitor (1µ)** | To stabilize power signal. | | Non-polarity |
| **Resistor (0 Ohm) x2** | To use as a bridge for tracks to run underneath. | | Non-polarity. |
| **Resistor (4.9k Ohm) x3** | To control amount of current going to the separate LEDs | | Non-polarity. |
......
......@@ -323,7 +323,7 @@ I felt confident enough in the boards I've previously produced to design these b
| **COMPONENT** | **DESCRIPTION** | **DATA SHEET** | **SPECIFICATIONS** |
|---|----|---|----|
| **3 UPDI Header pins** | To allow board programming/UPDI communication. Plus power 5v | | Non-polarity. |
| **ATtiny1614** | More pins than the ATtiny1614 | [ATtiny1614-16-17-DataSheet-DS40002204A.pdf](../week12/ATtiny1614-16-17-DataSheet-DS40002204A.pdf "ATtiny1614 datasheet") | Polarity |
| **ATtiny1614** | More pins and memory than the ATtiny412. | [ATtiny1614-16-17-DataSheet-DS40002204A.pdf](../week12/ATtiny1614-16-17-DataSheet-DS40002204A.pdf "ATtiny1614 datasheet") | Polarity |
| **Voltage regulator** | To drop the input voltage by 1.2 v for the sensor. | [LM3480_datasheet.pdf](../week10/lm3480.pdf) | Polarity |
| **Capacitor (1µ)** | To stabilize power signal. | | Non-polarity |
| **Resistor (0 Ohm) x6** | To use as a bridge for tracks to run underneath. | | Non-polarity. |
......
......@@ -23,6 +23,20 @@ draft: false
#### Guide
---
Dependencies from Electronics:
| **DIMENSION** | **VALUE** | **DESCRIPTION** |
|---|---|---|
|**LENGTH**| ??mm | Max length of the electronics board and it components. |
|**WIDTH**| ??mm | Max width of the electronics board and it components. |
|**HEIGHT**| ??mm | Max height of the electronics board and it components. |
||||
||||
||||
||||
||||
---
### BOM
---
......
......@@ -6,6 +6,9 @@ type: page
label: FINAL PROJECT - Plan
---
![Final Project - Plan - Development Trajectory](../plan/Development.jpg "Final Project - Plan - Development Trajectory")
## COMING SOON
| WEEK | TASK | DESCRIPTION | RATING | % | NOTES |
......@@ -19,7 +22,7 @@ label: FINAL PROJECT - Plan
|**7** | [RESEARCH](../research) | | | 0% | |
|**8** | [RESEARCH](../research) | | | 0% | Embedded Programming |
|**9** | [RESEARCH](../research) | | | 0% | |
|**10**| [RESEARCH](../research) | | | 0% | ----- BREAK -----|
|**10**| [RESEARCH](../research) | | | 100% | ----- BREAK -----|
|**11**| | | | 0% | Input Devices|
|**12**| | | | 0% | Moulding & Casting|
|**13**| | | | 0% | Output Devices|
......
Markdown is supported
0% or .
You are about to add 0 people to the discussion. Proceed with caution.
Finish editing this message first!
Please register or to comment